Over the years so many operators have died or sustained a vey serious injury because of lack of incentives on healthy tips on heavy machine operation. This article is not just to save life but to enlighten the mass on the dangers of not abiding to this safety rules.
Heavy equipment or earth moving machines have been recently reported due to multiple accidents and fatalities. It is a must that all operators have identifiable and verifiable training on the equipment before operating. Accidents can happen to both the newly trained and seasoned veterans.
Healthy Tips to Avoid Equipment Accidents
For everyone’s safety especially those of the operators, here are ten important heavy equipment safety tips.
1. Blind spots
Heavy equipment operators have to be 100% sure that no one is behind them or in their blind spots when moving, even if this involves getting out of the machine and checking. If vision is limited, have a spotter stand in a safe, visible position to guide and direct you. Inform those working around you for the day of your blind spots and require them to make eye contact with you before coming in the equipment’s vicinity. High visibility vests are mandatory on all sites.
Always be in constant communication with the people working around you. A two-way radio is the best form of communication, if that option is not available then use hand signals from a spotter who has been properly trained. Communication with operators should be touched upon at every safety meeting and reinforced by the foreman on site.
Wearing your seatbelt in heavy equipment is just as important as in a moving motor vehicle. There is no excuse but laziness for not wearing it at all times. Not only will it save your life in the case of a rollover, it keeps you firmly in your seat when operating on rough terrain, saving energy and reducing close calls by the end of a long day.
4. Mounting and Dismounting
Falls and stepping on and off are some of the biggest causes of injury recorded by OSHA and other safety departments. This includes entering and exiting the cab of a machine. A good rule of thumb is to always maintain a 3 point contact when getting on or off of your equipment and never jump. The three Point Rule requires three of four points of contact to be maintained with the vehicle at all times – two hands and one foot, or both feet and one hand. If handholds or steps are damaged, replace them, it could prevent major injury over time.
5. Loading/Unloading Equipment
Always be sure to be on level ground when loading or unloading your equipment. It greatly reduces the risk of rollovers or sliding off the low-bed ramps. If you are unloading on a busy jobsite or high traffic area, make sure people are clear of the unloading area and use a spotter to guide you.
6. Overhead and Underground Hazards
Before work starts on any jobsite, all over-head obstructions such as power lines and low clearance should be identified and flagged. Underground utilities such as water, sewer, gas, and electrical need to be located by the appropriate department and marked with colour coded paint. Play it safe when getting close to the underground utility and hand dig to uncover. When leaving dugout holes that workers or the public can fall in to, be sure to set up barriers and snow fencing.
In accordance with OSHA, employers must train and have procedures in place to ensure that before any employee performs servicing or maintenance on a machine where unexpected start-up or release of stored energy could occur and cause injury, the machine or energy source must be rendered inoperative. This includes hazards such as pinch points, attachments, and raised loads. Picture warnings, locks, and tags are to be used to prevent any incidents.
8. Load Limits
Be aware of the load limits of varying equipment when operating different machines throughout the day. Depending on the equipment set-up and size the load limits can change drastically. When lifting objects with a machine make sure loads are secure with the proper rigging attachments, and always inspect to ensure they are in good working condition. As with most equipment operations, confirm all workers are at a safe distant when lifting and moving loads.
9. Walk-around Inspection
Equipment should be inspected at least once daily before operating. This involves walking around with a pre-developed checklist of components to check for good working order. Hydraulic hoses, undercarriage, oil levels, stress points, etc. are all areas that need to be inspected and reported to the maintenance/safety department before machine start-up. Using a cloud-based mobile device to complete a task such as this can greatly improve communication and response time between operator and mechanic.
10. Knowing your Limits
Operating heavy equipment can be a stressful job at times even for a seasoned veteran. Never put yourself in a situation you don’t feel comfortable in regardless of your instructions. Get out and look if unsure about working on a slope or around hazards. Staying calm and alert throughout the day will allow you to be more productive will translate to a positive working environment for those around you.
As always, this list is only general guideline of things to keep in mind. Accidents can happen, but most are preventable incidents. Having regular safety meetings and up-to-date procedures and training will keep incidents down and work days more efficient.